PADS Layout need username and pssword?
I have a couple of users who for some reason is now required to enter username and password when starting PADS Layout.PADS Logic and PADS Router does not require this.It reacts in the same way as if it...
View ArticleNo able to import dxf into PADS Layout to create board outline
Hi,I try to import dxf into pads layout 9.5 to use it as board outline but I'm not able.I use import dxf under drafting toolbard but when I change the line from 2D to board outline appair...
View ArticlePowernet Latest Version
Hello, Where can I find the latest version of Powernet. ThanksRoger
View ArticleClik here to view.
How do I create an associated net so I can create a matched length group for...
I have a design where a bus of signals pass through a isolator and SSR to a connector. We want to eliminate any skew not associated with the isolator. Currently we set up each section...
View ArticleHow to relative move a selection?
Hello, how can I do a relative move of selected components? Bachground:I've a group of connectors that I've placed at given coordinates.But the origin of the PCB decals are set to pin 1 instead of the...
View ArticleClik here to view.
PADSvx12 - 3D thru hole parts issue
Why do the Thru hole parts sit above the pcb as SMT parts.
View ArticleHow do I set the plane/pour line width and hatch based on minimum trace/space...
I have a minimum trace/space requirement of 0.15mm. If I set the line width to 0.15 and that hatch spacing to 0.015, I get a contiguous flood, but the shape doesn't fill in within the default...
View ArticleExporting PADS 9.5 Files to 9.0
How do you export Mentor Graphics Designer Layout files to legacy PADS 9.0? Layout can create these files: .pcb, . dnf, and .csv. PADS needs .ascii. - RW
View ArticleWhat exactly does the demonstration mode in PADS Layout limit? (PADS 9.5)
Hi, Sometimes I'm unlucky and none of the floating licenses are available while I need to open PADS Layout. The software tells me that it will start in demonstration mode instead. What exactly does...
View ArticleSMA SMB and SMC Footprints, anyone?
I am using data sheets right now, and I am discovering that the footprints will vary. I was hoping the new Libraries from Mentor would have the SMA, SMB and SMC footprints in there, but they are not...
View ArticlePart created in Top with LP in Bottom Silkscreen
Hello , Is it possible to have LP on bottom silkscreen with part created on top ? I have a part which needs screw symbol on bottom silkscreen . So please help me for the same . -- Best Regards ,Parth...
View ArticleCAM Plus (Proper output of SMT parts with ThruPins)
We have SMT parts that also have Thru Pins. The parts keep showing up in the "ThruPin" output when they should be in the "SMT" output. Is there a way to define these parts so that they are placed in...
View ArticlePDF Configuration (Annotations)
File > Create PDF > PDF ConfigurationIs there a list of the default annotations that are displayed when the "Create annotations that will display part attributes" is enabled?Is there any way to...
View Article"* Failed to get PART from library"
I am attempting to make a PADS library on our network so coworkers can share the same library with our company's part numbers. My first attempt let me write a library file onto the network but when I...
View ArticleAdd via option in padstack editor is grayed out
I need to add some vias in the design. I have a integrated project that I have done and I need to add a couple of vias for routing and pouring now. The add via button is greyed out. How do we add the...
View ArticleHow to stimulate a PDN with a CPM model?
An IC vendor provide the CPM (chip power model) model and i am trying to carry on further investigation on a PDN's pcb board.The CPM looks like a Spice model with IPWL (current source) ports that...
View ArticleVia simulation issue when translating from Allegro to Hyperlynx
Hi, When I translate board file from Allegro to Hyperlynx. I use the via properties or visualizer in Hyperlynx boardsim. Via properties in Hyperlynx are very different from Allergor in terms of...
View ArticleEMA Acquires Accelerated Designs for its Extensive Part Library and Expertise
So what does this mean for the future of PartQuest since Accelerated Designs is providing the content? iconnect007 :: Article
View ArticleClik here to view.
PartQuest footprint not found
When I download a part through part quest I can see the symbol and data in xDX Databook but the footprint does not appear in the decal browser when i place the part on the schematic. What is the .d...
View ArticleClik here to view.
Can't get partquest to work with PADS VX1.2
I've been trying to get partquest to work with PADS VX1.2 without any success. I followed Gary's video but doesn't work as in the video.I am missing PartQuest directory and partquest.ini file after...
View Article